| Item | QTY. | Function | Unit Price | Total |
|---|---|---|---|---|
| IR Beam Break (Adafruit. Part ID:2167) | 1 | TOT Detection | 8.72 | 8.72 |
| SG90 Servo | 3 | Oxygen gauge, power gauge and tot | 2.20 | 6.60 |
| HS-645MG High Torque Servo - SPDL provided | 2 | Timer and cannon | 0.00 | 0.00 |
| DF5015 Small DC Fans | 4 | Air Leak game | 2.50 | 10.00 |
| A3144 Hall Effect Sensor | 3 | Air Leak game (non contact sensing) | 0.65 | 1.95 |
| 10mm Magnets | 3 | Air Leak game | 0.19 | 0.57 |
| 5mm Red LEDs | 24 | Meteorites | 0.04 | 0.93 |
| 5mm Blue LEDs | 1 | Cannon tip | 0.04 | 0.04 |
| 10mm Red LEDs | 3 | Warning LEDs | 0.59 | 1.77 |
| Push Button - SPDL Provided | 1 | Shoot the cannon | 0.00 | 0.00 |
| BVM1027 Coin Vibration Motor | 2 | Cannon feedback and warning buzzer | 0.75 | 1.50 |
| PCBs for LED arrays | 3 | Meteorites | 2.13 | 6.39 |
| 830 Point Solderless Prototype PCB Board | 3 | Circuits | 3.07 | 9.21 |
| Solder 6' | 1 | Circuits | 0.60 | 0.60 |
| Set 20 Molex Connectors and Wire | 1 | Circuits | 8.59 | 8.59 |
| 14pin DIP Socket | 3 | Holding 74HCT14 on PCB w/o soldering | 0.25 | 0.75 |
| 16 pin DIP Socket | 3 | Holding 74HCT595 on PCB w/o soldering | 0.25 | 0.75 |
| 10kΩ Potentiometer | 1 | For cannon | 0.83 | 0.83 |
| 2W10 Bridge Rectifier | 1 | Power crank circuit | 1.24 | 1.24 |
| 200Ω Resistor - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 220Ω Resistor - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 390Ω Resistor | 24 | Circuits | 0.01 | 0.24 |
| 470Ω Resistor - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 1kΩ Resistor - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 2.2kΩ Resistor - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 10kΩ Resistor - In lab kit | 9 | Circuits | 0.01 | 0.09 |
| 0.1uF Capacitor - In lab kit | 9 | Circuits | 0.00 | 0.00 |
| 10uF Capacitor - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 220uF Capacitor - In lab kit | 7 | Circuits | 0.00 | 0.00 |
| IRLZ34N N-Channel MOSFET - In lab kit | 4 | Circuits | 0.00 | 0.00 |
| 2N7000 N-Channel MOSFET - In lab kit | 3 | Circuits | 0.00 | 0.00 |
| MCP6294 Op Amp - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| LM324N Op Amp - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 74HCT14 Inverter Hex Schmitt Trigger - In lab kit | 1 | Circuits | 0.00 | 0.00 |
| 74HCT595 Shift Register - In lab kit | 4 | Circuits | 0.00 | 0.00 |
| Tiva Launch PAD - SPDL provided | 1 | Circuits | 0.00 | 0.00 |
| 5V/13V Power Supply- SPDL provided | 1 | Circuits | 0.00 | 0.00 |
| 3D Printed Oxygen Gauge | 1 | Air Leak game | 3.37 | 3.37 |
| 3D Printed Crank | 1 | Power the Dome game | 7.23 | 7.23 |
| 3D Printed Battery Gauge and Knob | 1 | Battery gauge and knob for potentiometer. | 6.29 | 6.29 |
| 3D Printed Hall Sensor Support and plug | 1 | Air Leak game | 5.40 | 5.40 |
| Duron 1/8" | 5 | Housing | 3.00 | 15.00 |
| Duron 1/4" | 2 | Housing | 4.00 | 8.00 |
| 2mm Flat Washers | 30 | To hold components to housing | 0.03 | 0.90 |
| 2mm Hex Nuts | 30 | To hold components to housing | 0.08 | 2.40 |
| 2mm Screws | 30 | To hold components to housing | 0.10 | 3.00 |
| Wood Glue - SPDL provided | Housing | 0.00 | 0.00 | |
| Paint - SPDL provided | Housing Decoration | 0.00 | 0.00 | |
| Total | 112.36 |